10 Responses to “Citrix Cloud (DaaS) Documentation Script V1.22”

1. Jeremy Holt Says:
   August 1, 2023 at 9:55 am

   Carl, I have a solution for users who get the Import-Module : A drive with the name ‘XDHyp’ already exists error.

   If this happens, close your powershell window and open a new one. add-pssnapin *citrix* then set-xdcredentials……. then do a get-psdrive. if xdhyp shows up in the list run: remove-psdrive xdhyp then run the cc_inventory_v1.ps1

   it will work this time.

2. Jeremy Holt Says:
   June 16, 2023 at 2:57 pm

   Carl,
   I ran into the error for…
   # “Import-Module : A drive with the name ‘XDHyp’ already exists.”

   I was able to resolve this by opening a new elevated Powershell window, then running…

   # get-psdrive

   if XDHyp is in the list, then run…

   # remove-psdrive XDHyp

   Then Set-XDCredentials, and then run the script again.

   This resolved the issue for me.

3. Kenneth Laury Says:
   December 14, 2022 at 11:26 pm

   We are using DAAS and I like the section part of your script. I want to run the script from a batch file , but because I’m using about 4 parameters from the Section the commas is causing my entries from being validated. I get something like Groups, is not a valid entry. The other thought was to try to hardcode parameters into the script, but limited knowledge of PowerShell is not helping. If you could give me any kind of help, I would appreciate it.

   • Carl Webster Says:
     December 18, 2022 at 1:08 pm

     I have asked my two main PowerShell mentors if they have any advice.

     Webster

4. Matt Moffat Says:
   November 22, 2022 at 6:51 pm

   I am using citrix daas and there are quite a few of the set-brokerserviceconfigurationdata options that I am wanting to configure. However, many of them return an error saying:
   “Configuration data setting name is unknown.”
   FullyQualifiedErrorId : Citrix.XDPowerShell.Broker.UnknownConfigurationDataSetting,Citrix.Broker.Admin.SDK.SetBrookerServiceConfigurationDataCommand

   2 examples of where I am seeing this is with
   Set-BrokerServiceConfigurationData “Hosting.MaxRegistrationDelayMin” -settingvalue 45
   Set-BrokerServiceConfigurationData “Hosting.MaxTimeBeforeStuckOnBootFaultSecs” -settingvalue 900

   Any thoughts would be appreciated. Sincerest apologies if this is not the right setting for this question. Either way though, I am massively grateful for your documentation and information.

   • Carl Webster Says:
     November 30, 2022 at 6:22 am

     It looks like Citrix changed it from Hosting. to HostingManagement.

     Try that.

5. Lee Prior Says:
   November 16, 2022 at 11:15 am

   Hey Carl,

   thanks for this, but it generates an error when running against current Citrix Cloud
   “Unable to import the Citrix.Host.Commands module”
   at script ps1: 36722 char:1

   I have the latest SDK and Policy Snap-In installed

   • Lee Prior Says:
     November 16, 2022 at 11:17 am

     Also generates an error:

     Import-Module : A drive with the name ‘XDHyp’ already exists

     • Carl Webster Says:
       November 22, 2022 at 5:47 pm

       # KNOWN ISSUE:
       # A few users report they get the following errors even in a new elevated PowerShell session:
       # “Import-Module : A drive with the name ‘XDHyp’ already exists.”
       # “ProcessScriptSetup : Unable to import the Citrix.Host.Commands module. Script cannot continue.”
       # Even if the script runs for these users, the Hosting section contains no usable data.
       # Hosting
       # Unable to retrieve Hosting Units
       #
       # Unable to retrieve Hosting Connections
       #
       # My-Hosting-ConnectioName
       # Connection Name My-Hosting-ConnectioName
       # Type Hypervisor Type could not be determined:
       # Address
       # State Disabled
       # Username
       # Scopes
       # Maintenance Mode Off
       # Zone
       # Storage resource name
       #
       # Advanced
       # Connection Name My-Hosting-ConnectioName
       # Unable to retrieve Hosting Connections
       # I have been unable to determine the root cause, a resolution, or a workaround for this issue

   • Carl Webster Says:
     November 22, 2022 at 5:47 pm

     # KNOWN ISSUE:
     # A few users report they get the following errors even in a new elevated PowerShell session:
     # “Import-Module : A drive with the name ‘XDHyp’ already exists.”
     # “ProcessScriptSetup : Unable to import the Citrix.Host.Commands module. Script cannot continue.”
     # Even if the script runs for these users, the Hosting section contains no usable data.
     # Hosting
     # Unable to retrieve Hosting Units
     #
     # Unable to retrieve Hosting Connections
     #
     # My-Hosting-ConnectioName
     # Connection Name My-Hosting-ConnectioName
     # Type Hypervisor Type could not be determined:
     # Address
     # State Disabled
     # Username
     # Scopes
     # Maintenance Mode Off
     # Zone
     # Storage resource name
     #
     # Advanced
     # Connection Name My-Hosting-ConnectioName
     # Unable to retrieve Hosting Connections
     # I have been unable to determine the root cause, a resolution, or a workaround for this issue